interface FastEthernet0/0
no ip address
duplex auto
speed auto
!
interface FastEthernet0/0.1
encapsulation isl 11
ip address 192.168.0.1 255.255.255.0
ip access-group v11 in
interface FastEthernet0/0.2
encapsulation isl 10
ip address 172.16.1.1 255.255.255.0
ip access-group v10 in
interface FastEthernet0/1
ip address 10.10.10.9 255.255.255.0
ip access-group v13 in

ip route 0.0.0.0 0.0.0.0 10.10.10.10

ip access-list extended v10
permit ip 172.16.1.0 0.0.0.255 172.18.0.0 0.0.255.255 reflect v133
permit tcp 172.16.1.0 0.0.0.255 172.18.0.0 0.0.255.255 reflect v133
permit udp 172.16.1.0 0.0.0.255 172.18.0.0 0.0.255.255 reflect v133
permit icmp 172.16.1.0 0.0.0.255 172.18.0.0 0.0.255.255 reflect v133
permit ip 172.16.1.0 0.0.0.255 192.168.0.0 0.0.0.255 reflect v111
permit tcp 172.16.1.0 0.0.0.255 192.168.0.0 0.0.0.255 reflect v111
permit udp 172.16.1.0 0.0.0.255 192.168.0.0 0.0.0.255 reflect v111
permit icmp 172.16.1.0 0.0.0.255 192.168.0.0 0.0.0.255 reflect v111
permit ip any any
ip access-list extended v11
evaluate v111
deny ip 192.168.0.0 0.0.0.255 172.16.1.0 0.0.0.255
deny icmp 192.168.0.0 0.0.0.255 172.16.1.0 0.0.0.255
deny udp 192.168.0.0 0.0.0.255 172.16.1.0 0.0.0.255
deny tcp 192.168.0.0 0.0.0.255 172.16.1.0 0.0.0.255
permit ip 192.168.0.0 0.0.0.255 172.18.0.0 0.0.255.255 reflect v133
permit udp 192.168.0.0 0.0.0.255 172.18.0.0 0.0.255.255 reflect v133
permit icmp 192.168.0.0 0.0.0.255 172.18.0.0 0.0.255.255 reflect v133
permit tcp 192.168.0.0 0.0.0.255 172.18.0.0 0.0.255.255 reflect v133
permit ip any any
ip access-list extended v13
evaluate v133
deny icmp 172.18.0.0 0.0.255.255 172.16.1.0 0.0.0.255
deny ip 172.18.0.0 0.0.255.255 172.16.1.0 0.0.0.255
deny udp 172.18.0.0 0.0.255.255 172.16.1.0 0.0.0.255
deny tcp 172.18.0.0 0.0.255.255 172.16.1.0 0.0.0.255
deny icmp 172.18.0.0 0.0.255.255 192.168.0.0 0.0.0.255
deny ip 172.18.0.0 0.0.255.255 192.168.0.0 0.0.0.255
deny tcp 172.18.0.0 0.0.255.255 192.168.0.0 0.0.0.255
deny udp 172.18.0.0 0.0.255.255 192.168.0.0 0.0.0.255
permit ip any any
ip access-list logging interval 100


以上配置实现三个等级的网段访问，使用于企业的总经理、财务、员工三个网段

测试方法：
配置完成之后，在不同网段使用ping命令开两个窗口，分别ping其他两个网段
这时在router 上用sh ip access-l 查看有没有产生你所需要的acl，如果没有，查看是哪一条acl起效（根据acl后面的条目数，ping的过程会有一个acl的条目逐渐增加）